Tyga Race Step Kit - Race - 2014-2021
STAA-0124
Street/Race shift possible by reversing the gear change arm. No other modification necessary other than adjustment of the Link Rod. Peg position is 25/40mm. up and 15/30mm. back. NOTE for PCv users: If you are going to use the Dynojet PCv quickshifter, you will want to also purchase the STAR-0185 Link Rod, which is 185 mm and short enough to replace the 205mm Link Rod provided with the kit. Yes, you can possibly turn the OD down on a lathe and rethread the existing Link Rod, but these Link Rods are made from a HARD stainless steel and they will chew up and spit out most threading dies. You will need to use either a cobalt or carbide die (or carbide threading insert to single point thread) the end of the rod. A HSS tool or die is NOT sufficient. I've tried! Buy the shorter 185mm Link Rod, and save yourself the aggrevation, profanity, and the eventual throwing of wrenches. If you do elect to cut down and thread the 205mm rod, be sure to cut off and thread the RH thread end, see profanity. ;) No provision for the side stand is provided. If you want to retain side stand use, you can either: | $334.81 |
|
Tyga Race Step Kit - Street - 2014-2021
STAA-0024
Race shift possible by reversing the gear change arm. No other modification necessary other than adjustment of the Link Rod. Peg position is 25/40mm. up and 15/30mm. back. NOTE for PCv users: If you are going to use the Dynojet PCv quickshifter, see note above on the STAA-0124 Race listing. Provision for the side stand is provided. This set is the same as the race set except it uses longer footpegs for more comfortable street use and retains the kickstand. All individual parts are available as spares. See bottom of page. | $354.42 |
|
Tyga Race Step Kit - Race - 2022+
STAA-0137
Street/Race shift possible by reversing the gear change arm. No other modification necessary other than adjustment of the Link Rod. Peg position is 25/40mm. up and 15/30mm. back. NOTE for PCv users: If you are going to use the Dynojet PCv quickshifter, you will want to also purchase the STAR-0185 Link Rod, which is 185 mm and short enough to replace the 205mm Link Rod provided with the kit. Yes, you can possibly turn the OD down on a lathe and rethread the existing Link Rod, but these Link Rods are made from a HARD stainless steel and they will chew up and spit out most threading dies. You will need to use either a cobalt or carbide die (or carbide threading insert to single point thread) the end of the rod. A HSS tool or die is NOT sufficient. I've tried! Buy the shorter 185mm Link Rod, and save yourself the aggrevation, profanity, and the eventual throwing of wrenches. If you do elect to cut down and thread the 205mm rod, be sure to cut off and thread the RH thread end, see profanity. ;) No provision for the side stand is provided. If you want to retain side stand use, you can either: | $371.02 |
|
Tyga Race Step Kit - Street - 2022+
STAA-0037
Race shift possible by reversing the gear change arm. No other modification necessary other than adjustment of the Link Rod. Peg position is 25/40mm. up and 15/30mm. back. NOTE for PCv users: If you are going to use the Dynojet PCv quickshifter, see note above on the STAA-0124 Race listing. Provision for the side stand is provided. This set is the same as the race set except it uses longer footpegs for more comfortable street use and retains the kickstand. All individual parts are available as spares. See bottom of page. | $390.59 |
|
Top Triple Clamp Clipons and Steering Stopper Set - 2014-2021
TYLY-1831
Racer package set which consists of the parts shown in the photo. The triple clamp, clipon handlebars, and steering stopper have been designed by TYGA Performance specifically for the KTM RC series and are a must for anyone taking their racing seriously. The triple clamp is designed round the stock dimensions but allows for removal of the ingnition lock holder for hard core racers. The handlebars are mounted seperately and can be positioned to your comfort and requirements, unlike the stock ones. In addition, in this kit is included a steering stopper to limit steering movement and prevents the bars from contacting bodywork or tank... resulting in a early morning Tech Inspection fail which NO racer ever has time for. Estimated Product Weight: 2.81lbs / 1.277kg Estimated Product Box Weight: 1.10lbs / 0.500kg | $412.62 |
|
Top Triple Clamp Set - 2014-2021
TYLY-1073
CNC machined top triple clamp with detachable ignition switch/lock holder for your KTM RC Series motorcycle Designed and machined in house by TYGA, as a direct replacement for the OEM top triple clamp. FEA tested and developed for increased strength without unnecessarily increased weight. Crafted from aircraft spec 6061-T6 alloy, the top triple clamp is ready to fit. The detachable ignition lock holder is positioned to allow use of the steering lock, but can be removed for race use. | $186.45 |
|
Top Triple Clamp Set - 2014-2021
TYLY-1073(p)
CNC machined TYGA top triple clamp. Intended for racers who have removed their ignition switch. Designed and machined in house by TYGA, as a direct replacement for the OEM top triple clamp. FEA tested and developed for increased strength without unnecessarily increased weight. Crafted from aircraft spec 6061-T6 alloy, the top triple clamp is ready to fit. | $136.94 |
|
Steering Damper Kit - 2014-2021
DAMPER-KIT
Racers and serious Street Riders asked, and we've answered! We are now able to offer a Steering Damper Kit for your RC390 to fit your budget and requirements. We can provide the damper itself, or just the mounting hardware. Damper Kit 2 works with the Tyga Triple Top, and is CNC manufatured to key into the triple perfectly! This is now our prefered method of the kit, as it works as if it were desited for the damper from the start! The damper iteself is a rotary damper, with 25 clicks of adjustment which is available to adjust while riding even. The high speed circuit will absorb the high energy hits and dampen out tank slappers and sudden jolts to the steering. There are 3 fully adjustable circuits in all. The damper mounts to the top of the Tyga triple clamp. The torque arm connects to a frame mount which safely and firmly clamps onto the frame and holds the pin firmly with no flex in the pin even with the damper set to it's highest setting. We've TRIED to get our mount to flex. It's a VERY rigid setup we know folks are going to love! The hardware kit frame mounts and damper mount comes annodized in either KTM Orange or Black. Damper Kits meet the need for racers who's clubs require dampers to be mounted, or those who just wish to settle down that front end for those who ride hard and desire a little extra stability... or an edge over the competition. | $375.00 |
|
Top Triple Clamp, CNC Black, KTM RC Series (2022-2023)
TYLY-1273
Designed and machined in house by TYGA, as a direct replacement for the OEM top triple clamp. FEA tested and developed for increased strength without unnecessarily increased weight. Crafted from aircraft spec 6061-T6 alloy, the top triple clamp is ready to fit.
| $186.45 |
|
Front Ride Height Adjuster - 2014-2021
TYLY-0120
These Ride Height Adjusters replace the blank end caps on the stock KTM RC390 front suspension. These caps allow the rider to increase and decrease the ride height of the front forks allowing for quick changes to steering geometry without having to go to the trouble of moving the forks up and down in the clamps. Supplied in black and clear anodised finish, these adjusters are as beautiful as they are functional. | $139.70 |
|
Brake Lever CNC, TYGA, Adjustable, Flip-Up Type (all years)
LEVB-7003
CNC machined from solid billet, these flip up type levers are made to a very high standard and are adjustable for reach and length. Estimated Product Weight: 0.49lbs / 0.223kg Estimated Product Box Weight: 0.18lbs / 0.082kg | $55.16 |
|
Clutch Lever CNC, TYGA, Adjustable, Flip-Up Type (all years)
LEVC-7003
CNC machined from solid billet, these flip up type levers are made to a very high standard and are adjustable for reach and length. Estimated Product Weight: 0.49lbs / 0.223kg Estimated Product Box Weight: 0.18lbs / 0.082kg | $55.16 |
|
Clipons Set - 2014-2021
TYLY-1631
This handlebar set is designed to be used with our triple clamp TYLY-1073 and allows for adjustability of the handlbars. The stock arrangement has the bars mounted directly to the triple clamp making them unadjustable and prone to causing damage to the triple clamp in the event of an accident. These bars are clamped directly to the fork leg and thus seperates them from the triple clamp making them less likley to be damaged in an accident and easier to repair/replace when they are. It also allows for a great deal of adjustabilty in both height and rotation and the bars are angled downwards slightly for a better position for racing. The clamping part is designed for the stock 51 mm. fork legs and can be used on other motorcycles with the same 51 mm. sized fork legs. Bar Inner Diameter is 15mm and is NOT natively compatible with the KTM Power Parts lever guards. It is possible to have an insert with threaded hole pressed into the end of the bar and accept the stock style lever guards. Sato Racing and Rizoma (or eBay Chinese copies) offer lever guards which will work with the tyga Clipons. | $210.90 |
|
Clipons Set - 2022+
TYLY-1431
Consisting of the following products: 1x TYLY-1731L Handlebar Clamp, Left, Hinge Type, Black, KTM RC Series This handlebar clamp is designed to be used with our TYGA top triples: TYLY-1073 (2014-2021) and TYLY-1273 (2022-2023) and can be used with other models with a 51 mm. clamping face on the fork leg. The clamp features a hinged design for quick and easy fitting. * The Handlebar angle is 7 degrees down. 1x TYLY-1731R Handlebar Clamp, Right, Hinge Type, Black, KTM RC Series 1x TYLY-2069A Handlebar Tube, Index Mark, Assy., Black 1x TYLY-2069B Handlebar Tube, Index Mark, Assy., Black | $210.90 |
|
Steering Stopper (2014-2021)
BPSY-0159
Designed and manufactured in house by TYGA Performance, this stainless steel steering stopper restricts the amount of steering angle on the KTM RC series. Ideal for racing and preventing smashed thumbs from 'tank slappers'. Installs in minutes. No special tools or dismantling of the bike required. Estimated Product Weight: 0.10lbs / 0.045kg Estimated Product Box Weight: 0.04lbs / 0.018kg | $15.98 |
|
Clipon Replacement Bar
TYLY-1569
Handlebar Tube (Assy), Black. Suitable for both left and right sides. Comes fitted with plastic bung in barend. | $20.72 |
|
Mirror Blanking Plates, L&R, CNC Silver (2014-2021)
TYLY-0185
Handy mirror blanking plates for your KTM RC125/200/250/390 No need for ugly cable ties on those all important track days. These CNC machined blanks will secure your cowling and keep you looking stylish. 2x Mirror Blanking plates and 4x 6x14 screws are supplied. Estimated Product Weight: 0.13lbs / 0.059kg Estimated Product Box Weight: 0.22lbs / 0.100kg | $48.24 |
|
Mirror Blanking Plates, L&R, CNC Black (2014-2021)
TYLY-1185
Handy mirror blanking plates for your KTM RC125/200/250/390 No need for ugly cable ties on those all important track days. These CNC machined blanks will secure your cowling and keep you looking stylish. 2x Mirror Blanking plates and 4x 6x14 screws are supplied. Estimated Product Weight: 0.13lbs / 0.059kg Estimated Product Box Weight: 0.22lbs / 0.100kg | $48.24 |
|
KTM Keyless Tank Cap (2014-2021)
TYLY-0223
This keyless racing fuel tank filler cap is CNC machined from billet aluminium and anodised black with a laser etched TYGA logo. Designed with finger tabs for easy removal while wearing gloves Supplied complete with seals and mounting hardware, it can be installed in minutes. This product is suitable for KTM RC series sports bike models (RC125/200/250 and 390) Fits all KTM RC models which are using the OEM filler cap with code: 90507008000 (2014-2016) but also may fit on later models using a 7 hole filler cap. If your tank cap is centered it will not fit. If your tank cap is offset from center and moved up, then it should. Unfortunatly KTM isn't clear which model years have which caps. | $54.42 |
|
KTM Keyless Tank Cap (2022+)
TYLY-1223
This keyless racing fuel tank filler cap is CNC machined from billet aluminium and anodised black with a laser etched TYGA logo. This keyless racing fuel tank filler cap is CNC machined from billet aluminium and anodised black with a laser etched TYGA logo. Designed with finger tabs for easy removal while wearing gloves. Supplied complete with seals, it can be installed in minutes and you can re-use the original screws. Fits all KTM RC models which are using the OEM filler cap with the hole offset towards the back (towards the rider) of the tank hole. If your tank cap is centered it will not fit. If your tank cap is offset from center and moved down, then it should fit. To our knowlege, this change was only made to the 2022 RC390 and up. | $63.57 |
|
Rear Stand spools - Black
TYLY-1209
This item is suitable for any motorcycle with M10 bolt holes for rear stand spools. NOTE: The Bajaj factory that produces the KTM RC390 and Duke 390 does not have the best QC standards where it comes to the thread pitch for the rear spools mount location locations on the swingarm. I have found that MOST are threaded and tapped correctly with Fine M10x1.25 pitch threads, but occasionally some swingarms have been tapped with Course M10x1.5 pitch threads. I have also found instances where the holes are not threaded at all, and even on one occasion where a broken tap was discovered stuck in a brand new bike and it came that way from the factory! Officially, the threads are supposed to be M10x1.25 pitch. Most likely, your swingarm will be threaded as such, but if the threads do NOT fit, then you (unfortunately) have one of the swingarms where the factory worker grabbed the wrong thread pitch tap when they hand tapped your swingarm. This is covered extensively in the online forums, so just be aware that the bolts may not fit. It's unlikely, but it is possible. If you start to thread in your spools, and the bolt doesn't thread in easily, STOP!!! Don't force it. Check your threads in the swingarm against the threads on the bolt, and ensure that they are the same. Sometimes, the threads just need to be cleaned. Sometimes, the swingarm has the correct size but wrong thread pitch. | $19.11 |
|
Rear Stand spools - Silver
TYLY-0209
This item is suitable for any motorcycle with M10 bolt holes for rear stand spools Estimated Product Weight: 0.18lbs / 0.082kg Estimated Product Box Weight: 0.22lbs / 0.100kg | $19.11 |
|
Axle Slider Kit (2014-2021)
TPER-2004
This kit is specifically designed for the KTM racer in mind. The axle sliders have been designed to help protect your bike in the event of a crash. Easy to install and look cool too in KTM orange and black. Now you really are ready to race!
Estimated Product Weight: 0.86lbs / 0.391kg Estimated Product Box Weight: 0.22lbs / 0.100kg | $42.56 |
|
Captured Wheel Spacers, Seals, and Bearings - Orange (2014-2021)
TPER-0003ORANGE
This comprehensive kit is specifically designed for the KTM racer in mind. The wheel spacers have been cleverly designed to be captured in the seals (instead of being loose as they are with stock set up), enabling quick and easy wheel removal and installation; essential when every minute counts to get out in time for a session or race. In addition, the spacers are all made out of high quality aluminium (6061-T6) instead of steel giving a useful saving of 65% in important unsprung weight. Finally, we provide a complete set of high quality Japanese Koyo wheel bearings to replace the not so good ones supplied from the factory. All in all, a useful and inexpensive upgrade. Now you really are ready to race! Included in this kit are the following components:
Estimated Product Weight: 1.37lbs / 0.623kg Estimated Product Box Weight: 0.66lbs / 0.300kg | $117.43 |
|
Captured Wheel Spacers, Seals, and Bearings - Silver (2014-2021)
TPER-0003SILVER
This comprehensive kit is specifically designed for the KTM racer in mind. The wheel spacers have been cleverly designed to be captured in the seals (instead of being loose as they are with stock set up), enabling quick and easy wheel removal and installation; essential when every minute counts to get out in time for a session or race. In addition, the spacers are all made out of high quality aluminium (6061-T6) instead of steel giving a useful saving of 65% in important unsprung weight. Finally, we provide a complete set of high quality Japanese Koyo wheel bearings to replace the not so good ones supplied from the factory. All in all, a useful and inexpensive upgrade. Now you really are ready to race! Included in this kit are the following components:
Estimated Product Weight: 1.37lbs / 0.623kg Estimated Product Box Weight: 0.66lbs / 0.300kg | $107.87 |
|
Aluminium Wheel Spacers Kit - Orange (2014-2021)
TPER-2003Orange
This kit is specifically designed for the KTM racer in mind. The wheel spacers have been cleverly designed to be captured in the seals (instead of being loose as they are with stock set up), enabling quick and easy wheel removal and installation; essential when every minute counts to get out in time for a session or race. In addition, the spacers are all made out of high quality aluminium (6061-T6) instead of steel giving a useful saving of 65% in important unsprung weight. Now you really are ready to race! Included in this kit are the following components:
Note: We also offer a similar product in orange and kits for the wheel spacers, bearing and seals | $60.34 |
|
Aluminium Wheel Spacers Kit - Silver (2014-2021)
TPER-1003Silver
This kit is specifically designed for the KTM racer in mind. The wheel spacers have been cleverly designed to be captured in the seals (instead of being loose as they are with stock set up), enabling quick and easy wheel removal and installation; essential when every minute counts to get out in time for a session or race. In addition, the spacers are all made out of high quality aluminium (6061-T6) instead of steel giving a useful saving of 65% in important unsprung weight. Now you really are ready to race! Included in this kit are the following components:
Note: We also offer a similar product in orange and kits for the wheel spacers, bearing and seals | $50.41 |
|
Heel Guard (carbon), Left, Replacement
BPCC-9007
Replacement Left heel guard for Tyga step kits Estimated Product Weight: 0.07lbs / 0.032kg Estimated Product Box Weight: 0.04lbs / 0.018kg | $30.59 |
|
Heel Guard (carbon), Right, Replacement
BPCC-9008
Replacement Right heel guard for Tyga step kits Estimated Product Weight: 0.07lbs / 0.032kg Estimated Product Box Weight: 0.04lbs / 0.018kg | $26.93 |
|
Tyga Step Kit Replacement Foot Peg (Long Type), Assy.
STAP-0001
Footpeg - 93mm Long - Replacement foot peg for your TYGA Step Kit, long type. Complete with M8x55 taper socket bolt for mounting and 3x 8mm washers. We recommend securing with thread locking agent to resist vibration. Estimated Product Weight: 0.22lbs / 0.100kg Estimated Product Box Weight: 0.04lbs / 0.018kg | $25.07 |
|
Tyga Step Kit Replacement Foot Peg (Short Type), Assy.
STAP-0003
Footpeg - 78mm Long - Replacement foot peg for your TYGA Step Kit, long type. Complete with M8x55 taper socket bolt for mounting and 3x 8mm washers. We recommend securing with thread locking agent to resist vibration. Estimated Product Weight: 0.22lbs / 0.100kg Estimated Product Box Weight: 0.04lbs / 0.018kg | $22.77 |
|
Tyga Step Kit Replacement Gear Shift Lever
STAL-0002
Replacement gear lever for your TYGA Step Kit. Complete with bearings. Estimated Product Weight: 0.33lbs / 0.150kg Estimated Product Box Weight: 0.66lbs / 0.300kg | $40.64 |
|
Tyga Step Kit Replacement Left Side Hanger Mount
STAH-0047A
Replacement Left Hanger Mount for your TYGA Step Kit. Complete with mounting bolts. Estimated Product Weight: 0.51lbs / 0.232kg Estimated Product Box Weight: 0.11lbs / 0.050kg | $47.68 |
|
Tyga Step Kit Replacement Left Side Hanger
STAH-0047B
Replacement Left hanger for your TYGA Step Kit. Complete with mounting bolts. Estimated Product Weight: 0.51lbs / 0.232kg Estimated Product Box Weight: 0.11lbs / 0.050kg | $27.30 |
|
Tyga Step Kit Replacement Link Rod, STAR-0205 - 205 mm.
STAR-0205
Uses M6x1 thread in one end and M6x1 L/H thread in the other. Includes both nuts. 205mm in length. Estimated Product Weight: 0.17lbs / 0.077kg Estimated Product Box Weight: 0.11lbs / 0.050kg | $8.44 |
|
Tyga Step Kit Replacement Link Rod, STAR-0185 - 185 mm.
STAR-0185
Power Commander 5 Quickshifter shorter rod - Uses M6x1 thread in one end and M6x1 L/H thread in the other. Includes both nuts. 185mm in length. Estimated Product Weight: 0.17lbs / 0.077kg Estimated Product Box Weight: 0.11lbs / 0.050kg | $8.44 |
|
Tyga Step Kit Replacement M6 LH F. Rod End SILBP6S
STRE-1006
Replacement Left Hand Thread Rod End joint for your TYGA Step Kit. Estimated Product Weight: 0.11lbs / 0.050kg Estimated Product Box Weight: 0.66lbs / 0.300kg | $3.91 |
|
Tyga Step Kit Replacement M6 RH F. Rod End SIBP6S
STRE-0006
Replacement Right Hand Thread Rod End joint for your TYGA Step Kit. Estimated Product Weight: 0.11lbs / 0.050kg Estimated Product Box Weight: 0.66lbs / 0.300kg | $3.91 |
|
Tyga Step Kit Replacement Rear Brake Lever
STAL-0001SK
Replacement Brake Lever for your TYGA Step Kit. Complete with bearings. Estimated Product Weight: 0.62lbs / 0.282kg Estimated Product Box Weight: 0.66lbs / 0.300kg | $39.31 |
|
Tyga Step Kit Replacement Right Side Hanger Mount
STAH-0048A
Replacement Right Hanger Mount for your TYGA Step Kit. Complete with mounting bolts. Estimated Product Weight: 0.51lbs / 0.232kg Estimated Product Box Weight: 0.11lbs / 0.050kg | $47.68 |
|
Tyga Step Kit Replacement Right Side Hanger
STAH-0048B
Replacement Right hanger for your TYGA Step Kit. Complete with mounting bolts. Estimated Product Weight: 0.51lbs / 0.232kg Estimated Product Box Weight: 0.11lbs / 0.050kg | $34.19 |
|
Tyga Step Kit Replacement Sidestand Spacer
STAH-0047C
TYGA Step Kit replacement Sidestand Spacer Estimated Product Weight: 0.66lbs / 0.300kg Estimated Product Box Weight: 0.04lbs / 0.018kg | $23.08 |
|
Tyga Step Kit Replacement Rear Brake Link Pin
STAC-0012
This replacement part fits to the Tyga step kit brake lever on the KTM RC390 etc. Estimated Product Weight: 0.04lbs / 0.018kg Estimated Product Box Weight: 0.04lbs / 0.018kg | $9.21 |
|
Tyga Step Kit Replacement Bush, Pair, 20mm
STHB-0020
Tyga Step Kit Replacement Bush, Pair, 20mm Estimated Product Weight: 0.04lbs / 0.018kg Estimated Product Box Weight: 0.04lbs / 0.018kg | $6.14 |
|
Tyga Step Kit Replacement Bush, Pair, 30mm
STHB-0030
Tyga Step Kit Replacement Bush, Pair, 30mm Estimated Product Weight: 0.04lbs / 0.018kg Estimated Product Box Weight: 0.04lbs / 0.018kg | $6.61 |
|
Carbon Workshop Tray 300x200
TYTO-0004A
Using high end automotive and aerospace technology, this useful and beautiful tray will be the envy of all your friends and racing competitors and we promise that it will become an essential and indispensable part of your tool kit, as it has ours! The tray is both lightweight and extremely strong due to the method of construction and the materials used. Using a balance of craftsmanship and technology, each tray is individually laminated by skilled workers in a precision aluminium mold where it is subjected to high pressure to give unrivalled crisp and sharp finish which is both chemical and abrasion resistant. We have been testing these trays for several months now and given them no mercy. We have put brake fluid, carburetor cleaner, engine oil, gasoline and other nasty fluids in them and they have retained both their strength and beautiful sheen. We have used them to hold various motorcycle parts and tools and apart from minor surface scratching which is to be expected, the hard epoxy finish has proven to be extremely tough and durable, but forgiving enough not to damage any delicate parts. Of course, like all trays, these can be used around the home for drinks, fruit bowl and other decorations. If you have an application or require a similar product in large quantities, please contact us and we will be happy to discuss all details including design through to manufacturing and delivery. These trays are easily stackable and weigh only 240 grams
| $63.97 |
To read all about our Packaging, Shipping, and returns policy click here